How to Measure for Tile
Measuring floors, walls, and shower surrounds for tile, including L-shaped rooms, fixtures, and working in centimetres.
Area first, tiles second
Tile ordering goes wrong in a predictable sequence: someone measures loosely, converts area to tiles in their head, buys by the box at the shop, and discovers the shortfall with the floor half laid and the adhesive already mixed. The fix is procedural. Measure the surface carefully to get a true area, decide the waste allowance as a separate conscious choice, and only then turn area into tile and box counts. The Tile Calculator handles that last conversion flawlessly — your job is to hand it an area that deserves its precision.
Carry a tape measure (a 25 ft / 7.5 m tape suits floors; a shorter one is handier inside a shower), a notebook, a pencil, and a straight edge for marking. Sketch each surface as a rectangle or a set of rectangles before measuring anything, and write dimensions on the sketch as you take them. Photograph the finished sketch with your phone as insurance against a lost notebook somewhere between home and the tile shop.
Floors: the rectangle and its exceptions
A rectangular floor needs two measurements: length and width, taken wall to wall at the skirting line. Measure the length twice, at opposite sides of the room. In older properties the walls may not be parallel, and differences of an inch (25 mm) or more over a room’s length are common. Use the larger figure for area — tile must cover the widest span, and the excess disappears into cuts at the far wall. Multiply length by width for area: a floor of 12 ft by 9 ft (3.66 m by 2.74 m) is 108 sq ft (10.03 m²).
Measure into doorways. The tiled surface usually runs to the threshold strip or halfway under the door leaf, not to the main room’s wall line. Each doorway adds a small rectangle — typically about 3 ft wide by a few inches deep (roughly 0.9 m by 0.1 m) — and omitting two of them can quietly remove a box’s worth of tile from the order on a small floor. Similarly, measure into the recesses beside a chimney breast, under a radiator only if you genuinely intend to tile beneath it (most do, for a finished look, after temporarily removing it), and inside any built-in cupboard whose door opens onto the tiled area.
Deduct almost nothing. A bath panel footprint, a pedestal basin, and a toilet base sit on top of or within the field, but tiling conventionally runs under or up to fixtures with the subfloor continuous beneath, and the patches involved are small. Kitchen islands are the honest exception: a fixed island’s footprint — say 6 ft by 3 ft (1.83 m by 0.91 m), 18 sq ft (1.67 m²) — is genuinely never tiled, and on a large floor that deduction is worth taking. Even then, many tilers tile through and accept the cost for the freedom to remodel later. Decide deliberately rather than by default.
L-shaped and irregular floors: divide and conquer
An L-shaped room defeats a single length-times-width attempt, but it surrenders immediately to division. Split the L into two rectangles with a line drawn on your sketch, measure each rectangle fully, calculate both areas, and add them. A kitchen-diner might resolve into a main block of 14 ft by 10 ft (4.27 m by 3.05 m) giving 140 sq ft (13.01 m²), plus a leg of 6 ft by 5 ft (1.83 m by 1.52 m) giving 30 sq ft (2.79 m²), for a total of 170 sq ft (15.79 m²). Check your split by measuring the overall extents as well; the bounding rectangle minus the missing notch should equal the sum of your two blocks, and if the two methods disagree, the tape work needs a second pass.
The same division handles bays, alcoves, and hearths. A fireplace hearth that will be tiled in the same material adds its rectangle; a hearth in a contrasting slate is measured separately and ordered as its own small quantity. Angled walls — common in extensions and loft rooms — produce triangles: base times height divided by two. A triangular infill with a 4 ft (1.22 m) base and a 3 ft (0.91 m) depth contributes 6 sq ft (0.56 m²). Curved boundaries, such as around a freestanding bath used as a tiling guide, are best approximated by the rectangle that contains the curve; the surplus becomes cutting waste, which the allowance would have consumed anyway.
Walls and splashbacks: height enters the picture
Wall tiling multiplies width by height instead of length by width, but the habits are the same. For a kitchen splashback (backsplash in US usage), measure the total run along the worktop in sections — cooker interruptions, window sills, and extractor hoods break the run into pieces with different heights. The strip between worktop and wall cabinets is often around 18 in (about 45 cm), yet it varies, so measure your own gap at several points and use the greatest. Above a range cooker or hob, the height to the hood or ceiling forms a separate taller rectangle. Sum the sections rather than averaging them.
Full-height bathroom walls are measured per wall, then summed, because heights and widths differ once a window or door interrupts. For each wall: width times ceiling or tile height, minus the true area of any window or door opening within the tiled zone. Unlike paint, where standard deductions are fine, tile openings deserve real measurements — a window in a shower wall is also a surface in its own right, since its reveals (the sides inside the opening) are usually tiled too. Add each reveal as a narrow rectangle: depth of the wall thickness times the opening’s height or width.
Shower surrounds: a verified example
A shower enclosure concentrates every wall-measuring issue into a small space, so it makes a good test of method. Consider a typical arrangement whose tiled walls total 90 sq ft (8.36 m²) — for instance, a back wall and two side walls above a tray or bath, measured individually and summed after subtracting a small window. The tiles chosen are 12 in by 12 in (about 30 cm by 30 cm) squares, each covering exactly 1 sq ft.
The field alone would need 90 tiles. Shower work earns a 15 percent waste allowance rather than the 10 percent of an open floor, because nearly every course meets a corner, a shower valve, a niche, or the tray edge, and small enclosed areas mean a high proportion of cut tiles. Applying it:
90 × 1.15 = 103.5, rounded up to 104 tiles
At 12 tiles per box, that is 9 boxes (since 8 boxes would provide only 96). Note the double rounding working in your favour: the fractional tile rounds up, then the fractional box rounds up, leaving a handful of genuine spares beyond the allowance. That is the correct direction for rounding to err. Niches deserve a line of their own in the sketch — a recessed shelf of 12 in by 16 in (30 cm by 40 cm) has a back, two sides, a top, and a sill, and while its total area is small, every face is a cut piece, which is precisely what the elevated allowance is for.
Also measure the shower’s vertical extents honestly. Tiling to the ceiling in a wet zone is increasingly standard, and the difference between tiling to 78 in (about 2 m) and to a 96 in (2.44 m) ceiling across three walls is a box or more. Decide the finished height, including whether a border or trim row caps the field, before the area is finalised.
Working in centimetres without conversion pain
Metric measuring suits tile particularly well because so many tiles are manufactured to metric modules: 300 mm by 600 mm, 200 mm by 100 mm, and so on. Measure the room in centimetres, convert to square metres by multiplying metres by metres, and keep one conversion in your pocket: 1 sq ft equals 0.0929 m², and 1 m² equals 10.764 sq ft. A floor recorded as 420 cm by 310 cm is 4.20 m by 3.10 m, giving 13.02 m² — about 140 sq ft if a US-sourced calculator or product listing needs imperial.
Within a metric measurement, tile counts can be sanity-checked by module: a 300 mm by 300 mm tile covers 0.09 m², so a 9 m² wall needs 100 tiles before waste. If the calculator’s answer and your module check disagree wildly, a units slip — centimetres typed where metres belonged — is the usual culprit, inflating or deflating the area by a factor of 100 in a way that is obvious only if you look for it.
Whichever system you choose, measure the whole job in it. A floor in feet, a splashback in centimetres, and a shower remembered “about so big” will eventually be combined by tired arithmetic at a shop counter, which is where orders go to die.
From area to order, and the final checks
With areas settled per surface, apply waste by surface type rather than one blanket figure: open floors at the lower end, intricate patterns and wet zones higher — the reasoning behind pattern-driven allowances is set out in Herringbone Tile Waste Explained. Add border tiles, feature strips, and trim pieces as separate counted items, not as area; a pencil trim is bought by the length, so measure its run in feet or metres and round up to whole pieces.
Before ordering, reconcile three numbers: the summed sketch areas, the calculator’s total, and the box count times the box’s stated coverage. They will not match exactly — waste and rounding see to that — but they should tell a consistent story. Confirm the shop’s returns policy for unopened boxes, order everything in one batch to avoid shade variation, and keep the sketch. When the tiler (or future you, mid-job, adhesive on your hands) asks why there are eleven boxes for a ten-box floor, the sketch is the answer.
Next step: add up the separate floor and wall areas you measured and run each through the Tile Calculator on its own. Surfaces measured separately deserve waste applied separately, especially when one is a floor and the other a shower wall.