Tile Calculator

Tiles are not bought by the square foot — they are bought by the box, and the number you need depends as much on the pattern you lay as on the size of the room. This calculator counts tiles, adds the right waste for your layout, and rounds up to whole boxes.

straight grid — counted by area, offcuts reuse on the opposite wall herringbone detail — every border tile is cut at 45°, so waste rises same tiles, same room — the pattern is what changes the order
The two layouts this calculator prices differently. A straight grid reuses its row-end offcuts; a herringbone field turns most border offcuts into triangles the pattern cannot absorb, which is why its waste setting is double.

How to use the tile calculator

Start with the true area. For a floor, multiply length by width; for a bathroom with an L-shaped floor, split it into two rectangles, add them, and enter the total (the Square Footage Calculator handles the shapes). Enter the tile's full face size in inches — the size printed on the box, not the size after grout lines. Grout joints are already absorbed by the waste allowance, because a 3 mm joint on a small tile and a 5 mm joint on a large one both end up within the rounding of a whole box. Then choose the layout honestly. The pattern decision is where most tile orders go wrong: a straight grid in a rectangular room wastes very little, while a herringbone floor can turn a fifth of your tiles into triangular offcuts that fit nowhere.

If tiles are sold by the box, enter the count per box and the calculator rounds your order up to full boxes. Keep that rounding — a box short on the final Saturday of the job can mean a different production batch, and tile shades genuinely vary between batches. Buy everything in one order, check the batch or calibre numbers printed on the boxes match, and keep one spare box unopened if you can; future repairs with the same batch are worth far more than the refund.

The formula, and why waste is a pattern question

The calculator divides your area by one tile's area to get the exact tile count, then multiplies by one plus the waste percentage, and rounds up. A 12 × 24 in tile covers exactly 2 sq ft, so a 40 sq ft floor needs 20 tiles before waste. Waste is not carelessness — it is geometry. Every wall edge forces cuts; every cut risks a chip; diagonal layouts force cuts along all four walls instead of two; herringbone forces angled cuts at every border tile, and the offcut from a 45-degree cut is a triangle that can only be reused in a few places. That is why the allowances step from 5% for a big, square, straight-laid room up to 20% for herringbone, rather than using a single flat figure for everything.

Worked example: a small bathroom floor

A bathroom floor of 8 × 5 ft is 40 sq ft (3.72 m²). With 12 × 24 in porcelain tiles laid straight at 10% waste, the exact count is 40 ÷ 2 = 20 tiles, plus 10% gives 22 tiles. Sold ten to a box, that is 3 boxes — 30 tiles arriving, 22 planned, and a comfortable margin for the two awkward cuts around the toilet waste pipe and the door threshold. Now lay the same floor in a diagonal pattern at 15%: the count rises to 23 tiles, still 3 boxes, which is why small rooms forgive pattern ambition. Scale the room up and the pattern tax becomes real money, as the table below shows.

Worked example: a kitchen splashback

Small areas punish small tiles, and a splashback shows why. The run between a worktop and the wall units is typically 10 ft long and 1.5 ft high, which is 15 sq ft (1.39 m²) of tile. In 4 × 4 in tiles, each tile covers 0.11 sq ft, so the exact count is 15 ÷ 0.11 = 135 tiles; at the standard 10% waste for a straight lay the calculator returns 149 tiles, and sold in boxes of 50 that is 3 boxes. Two lessons hide in that small job. First, the count is dominated by the tile, not the room: the same splashback in 12 × 24 in tiles needs just 8 tiles before waste, and a single breakage is a much larger share of the order. Second, splashbacks are cut-heavy out of proportion to their size — every socket, corner and window sill interrupts the field — so the 10% here is doing more work than the same 10% on an open floor, and dropping to the 5% setting because "it is only a little wall" is the classic way to run out with one row left.

Waste allowances by layout

LayoutSuggested wasteWhere the waste goes
Straight grid, rectangular room5–10%Edge cuts along two walls; most offcuts reuse on the opposite wall
Offset / brick bond10–15%Staggered ends add cuts; offcuts reuse less predictably
Diagonal (45°) grid15%Triangular cuts along all four walls
Herringbone or chevron20%Angled cuts at every border; many offcuts are unusable shapes
Small rooms with many obstaclesAdd 5% to any row abovePipework, pedestals and doorways multiply the cut count

Common tile-ordering mistakes

Ordering by area alone — "the room is 40 square feet, the box says it covers 10, so four boxes" — ignores both waste and the fact that tile coverage printed on boxes assumes zero cuts. The second mistake is measuring the room but not the tile: nominal tile sizes lie, and a tile sold as 12 in may be 11⅞ in, which across a long wall adds up to a visible drift in your grout lines; measure a real tile from the box you will actually buy. Third is forgetting the vertical surfaces in a bathroom — the bath panel, a boxed-in pipe run, a splashback zone — which are rarely in the original floor measurement. Fourth is planning cuts to land exactly on fixtures: if your count only works when every cut around the toilet is perfect, it does not work. Finally, remember tiles are heavy and deliveries are kerbside; ordering the correct number in one delivery beats two deliveries and a batch mismatch.

Tile calculator FAQ

Does the calculator include grout and adhesive quantities?

No — it counts tiles and boxes only. Grout consumption depends on joint width and tile thickness in a way that deserves its own careful estimate; our guide to grout joints and tile spacing explains how joint width changes both the look and the materials list.

Why does herringbone need so much more waste?

Because the pattern meets every wall at an angle, so nearly every border tile is cut diagonally and its offcut is a shape the pattern cannot absorb. Our herringbone waste guide walks through a 60 sq ft entryway where 20% waste means 288 small-format tiles.

Should I really keep a spare box?

Yes, if storage allows. A cracked tile in five years can only be invisibly repaired with the same batch. Tiles are discontinued constantly; the spare box is the cheapest insurance on the whole job.

How do I measure a shower enclosure?

Measure each wall separately — height times width — and add them. A typical three-wall shower surround of 90 sq ft with 12 × 12 in tiles at 15% waste needs 104 tiles. The measuring guide for tile covers niches, benches and sloped ceilings step by step: how to measure for tile.

What about floor tiles for the walls of the same room?

Add the wall area to the floor area only if the same tile, laid the same way, covers both. Different patterns mean different waste rates, so run the calculator twice and add the boxes, not the areas.

See a complete bathroom worked end to end in the small bathroom floor estimate, including the cuts around the fixtures.

Sources for the rates on this page

The waste bands and installation practice behind this calculator follow the TCNA Handbook for Ceramic, Glass, and Stone Tile Installation (Tile Council of North America), read with the installation-system guidance published by Schluter Systems and the product and grout data published by MAPEI. The full source list is on the methodology page.