Paint Calculator

Enter the room, tell the calculator what will not be painted, and it returns the paint you actually need — in US gallons and litres, rounded up to whole cans you can buy.

room length — 12 ft in the worked example window — deduct 15 sq ft room width — 12 ft door — deduct 21 sq ft gross wall area = perimeter × ceiling height, then deduct the openings
The plan this calculator works from: the four walls are measured as a perimeter, the ceiling height is measured on the wall itself, and standard areas come back off for the door and window before coats and coverage are applied.

How to use this paint calculator

Measure the room's length and width along the floor with a tape measure, rounding each measurement up to the next tenth of a foot rather than down — paint estimating is one job where rounding down always costs you a second trip to the shop. Measure the ceiling height in two corners; older houses often differ by an inch or more from one side of a room to the other, and you should use the taller figure because the longer wall is the one that drinks the paint. Count the doors and windows honestly. A standard interior door with its frame is treated here as 21 square feet (about 1.95 m²) and a typical window as 15 square feet (about 1.4 m²), which matches the sizes most estimators use. If your home has a wide picture window or double doors, count it as two.

Next, set the number of coats. Two coats is the honest default for almost every repaint: one coat over a similar colour can look acceptable in flat light, but it rarely survives a sunny afternoon without showing roller marks and thin patches. Choose three coats when you are covering a much darker colour with a pale one, and one coat only for a same-colour refresh of a wall that is already in good condition. Finally, check the coverage figure. The calculator starts at 350 square feet per US gallon (roughly 8.6 m² per litre), the standard figure printed on most US paint cans for smooth, primed walls. Drop it towards 300 if your walls are rough, heavily textured or unpainted plaster, because porous surfaces absorb the first coat into the wall instead of leaving it on the surface.

The formula this calculator uses

The maths is deliberately simple enough to check on the back of an envelope. First the calculator finds the gross wall area: it adds the length and width, doubles that sum to get the full perimeter, and multiplies by the ceiling height. For a 12 × 12 ft room with 8 ft ceilings that is 2 × (12 + 12) × 8 = 384 square feet of wall. It then subtracts 21 square feet for every door and 15 square feet for every window, giving the net paintable area. Paint needed is the net area multiplied by the number of coats, divided by the coverage rate. Nothing else is hidden in the calculation: there is no secret fudge factor, and the waste you need for spills and cutting-in is handled by rounding the final answer up to whole cans rather than by inflating the area.

Worked example: a 12 × 12 ft bedroom

Take the bedroom above: 12 ft long, 12 ft wide, 8 ft ceilings, one door, one window, two coats at standard coverage. The perimeter is 48 ft, so the gross wall area is 48 × 8 = 384 sq ft. Deduct the door (21 sq ft) and the window (15 sq ft) and the net area is 348 sq ft, which is 32.33 m². Two coats over 348 sq ft means painting 696 sq ft of surface in total. Dividing 696 by the coverage rate of 350 sq ft per gallon gives 1.99 US gallons — 7.53 litres. Because paint is sold in whole cans, the calculator tells you to buy 2 one-gallon cans. That near-exact match is a coincidence of this room size, but it shows why guessing "one gallon per room" fails so often: a slightly larger room, or a third coat, pushes you firmly into a third can, while a small box room painted in one coat needs barely half of one.

Coverage rates: what changes them

Surface / situationTypical coverage per US gallonApprox. per litreWhy it differs
Smooth, previously painted wall, roller applied350–400 sq ft8.6–9.8 m²The surface is sealed, so nearly all paint stays on top
New plaster or bare drywall, first coat250–300 sq ft6.1–7.4 m²The porous surface absorbs paint; a primer coat reduces this loss
Lightly textured walls (orange-peel, light stipple)300–325 sq ft7.4–8.0 m²Texture increases the true surface area beyond the flat measurement
Heavy texture, brick or rough render200–250 sq ft4.9–6.1 m²Deep relief hides a lot of paint in its valleys
Spray applicationReduce any figure above by 15–25%—Overspray and bounce-back never reach the wall

UK readers should note that British cans are labelled in litres with coverage quoted per litre, commonly around 13 m² per litre for a single coat on a smooth surface — a theoretical figure that assumes a thinner film than most US labels. The calculator avoids this confusion by converting its US-gallon result into litres at 3.785 litres per gallon, so a 2-gallon answer is 7.53 litres of paint whichever side of the Atlantic you buy it on. If you are buying 5-litre or 10-litre tubs in the UK, compare the litres figure, not the can count.

Common mistakes that leave people short of paint

The most common error is painting the room in your head instead of the room on the tape: using the floor dimensions from a property listing, which are often measured to the outside of walls or rounded for marketing. The second is forgetting the wall above doors and windows — the calculator deducts only the opening itself, which is correct, but people estimating by hand often deduct the whole wall section. Third is planning one coat for a colour change; a deep red or navy under a pale grey will grin through a single coat almost everywhere. Fourth is ignoring the ceiling line and the wall inside wardrobes and alcoves: alcoves add wall area that a simple length × width misses, so measure any recess wider than a foot as its own small rectangle and add it. Finally, do not buy exactly the calculated amount of a mixed-to-order colour without a small reserve. Keeping half a litre back for touch-ups is far cheaper than having a new batch mixed months later and finding the shade has drifted.

Paint calculator FAQ

Should I deduct doors and windows at all?

For a single standard door or window the difference is small — about a twentieth of a gallon each — so some estimators skip deductions and treat the surplus as their waste allowance. Deduct when a room has several openings, patio doors or a large picture window, because then the overestimate can reach a full can. This calculator deducts standard sizes so the worked example stays honest, and the round-up to whole cans still leaves you a working margin.

Does the calculator include primer?

No. Primer is a separate product with its own coverage, and it is only needed on bare plaster, bare wood, stained surfaces or dramatic colour changes. If you prime, run the calculator once for the primer coat with coats set to 1, then again for your topcoats. Our guide to primer versus paint explains which surfaces genuinely need it.

How much paint for the ceiling as well?

Ceilings are calculated differently because texture matters more than openings, so use the dedicated Ceiling Paint Calculator, which applies a texture factor instead of deductions. A smooth 12 × 12 ft ceiling in two coats needs about 0.82 gallons.

Why does my can promise more coverage than the calculator assumes?

Label coverage is measured under laboratory conditions on a sealed, perfectly smooth panel. Real walls have texture, porosity and a decorator who loads the roller unevenly. Planning at 350 sq ft per gallon and being pleasantly surprised is better than planning at the label maximum and running out on the last wall. There is more detail in our coverage rates guide.

What if my room is not a rectangle?

Split it into rectangles, run each through the calculator, and add the gallons together before rounding up to cans. For the floor area of an L-shaped room, the Square Footage Calculator has a dedicated L-shape mode.

Planning a whole room? The worked 12 × 12 bedroom estimate combines walls and ceiling into one shopping list, and the guide to how much paint a 12 × 12 room needs explores how the answer moves with coats and room size.

Sources for the rates on this page

The 350 sq ft per gallon planning figure and the way label coverage is stated follow the coverage data paint manufacturers publish for their own products — principally Benjamin Moore's paint calculator and coverage guidance in the US and Crown Paints' paint calculator in the UK, whose per-litre figures are the source of the UK note above. Our methodology page sets out the full source list.