Measuring a Room for Flooring

How to measure rectangles, L-shaped rooms, closets and alcoves accurately before you order flooring.

Start with the bare room, not the floor that is already there

A tape measure tells you about the space you have today. Old carpet, laminate or vinyl tells you about a previous decision, and the two rarely agree. Fitters trim material under skirting boards, tuck edges into doorways and sometimes stop short beneath fitted furniture. If you copy the dimensions of a covering you are about to rip up, you inherit every shortcut taken last time.

Clear the perimeter first. Move what you can, and where a wardrobe or bookcase is too heavy to shift, measure to its front edge and then add its depth separately as a small rectangle of its own. Photograph each wall with your phone before you begin. The pictures cost nothing and they settle arguments later about which doorway had a step and which corner was not square.

Work with a partner if the room is longer than your tape. A sagging tape that droops in the middle reads long, and a solo measurement across a 16 ft (4.88 m) span can easily drift by half an inch (13 mm). Hook the end over a nail, weigh it down with a heavy book, or use a laser measure for the long runs and confirm one of them with the tape. Two methods agreeing is worth more than either method used twice.

The plain rectangle, done properly

For a simple oblong, multiply the longest wall by the widest wall. Take each dimension twice, at different heights along the wall, because rooms lean. A bedroom might read 12 ft 3 in (3.73 m) at one end and 12 ft 7 in (3.84 m) at the other where a chimney breast or a bowed stud wall intrudes. Always carry the larger figure forward. Flooring has to cover the widest point; the narrower end simply produces a slightly wider offcut.

Round up, never down, and round up to the next whole inch (or next centimetre if you are working in metric). Flooring is sold to cover area, and suppliers expect you to arrive with a ceiling figure rather than a precise one. Write the numbers on a sketch as you go. A sketch with arrows beats a list of figures because the list cannot tell you which number belonged to which wall once you are standing in a shop.

Check for square by comparing the diagonals. In a true rectangle both diagonals match. If yours differ by more than about an inch (25 mm) over a typical room, the corners are not right angles, and you should plan cuts accordingly rather than discovering it with the last plank in your hand.

Breaking an L-shape into two rectangles

Most awkward rooms are really two rectangles sharing a corner. Draw the outline, then draw one dividing line that splits the shape into a big block and a smaller block. Measure each block as if it stood alone, calculate both areas, and add them together.

Take a concrete illustration. One block measures 16 ft by 12 ft (4.88 m by 3.66 m), which is 192 sq ft (17.84 m²). The adjoining block measures 8 ft by 10 ft (2.44 m by 3.05 m), which is 80 sq ft (7.43 m²). Added together they give 272 sq ft (25.27 m²). That total is the net area your new floor must cover before any allowance for cutting waste, which is a separate question covered in our companion piece on waste allowances by layout pattern.

The dividing line can run either way. Splitting an L horizontally or vertically yields the same total, so pick whichever split gives you measurements you can physically take without climbing over furniture. If both splits are possible, do both and compare. Agreement is a cheap accuracy check; disagreement tells you a wall is not where your sketch thinks it is.

Avoid the trap of measuring the full length and full width and then subtracting the missing corner unless you are confident about that corner. Subtraction magnifies small errors. Two positive measurements added together are easier to verify on site than a large figure minus a small one estimated from a cramped nook.

Closets, alcoves, bays and hearths

Small projections are where estimates quietly fall short.

  • Closets and wardrobes (built-in cupboards). If flooring will run inside, treat the closet as its own tiny rectangle and add it. A 2 ft by 4 ft (0.61 m by 1.22 m) closet is only 8 sq ft (0.74 m²), yet forgetting three of them wipes out your waste margin. If the closet keeps its existing floor, leave it out entirely and note that choice on the sketch.
  • Alcoves either side of a chimney breast. Measure the main room to the face of the breast, then measure each alcove separately from the breast face to the back wall. Alcoves are frequently unequal, so never measure one and double it.
  • Bay windows. Approximate a shallow bay as a rectangle using its depth and its widest width. Curved or angled bays waste more material than the arithmetic suggests, which is another reason the waste allowance matters.
  • Hearths and thresholds. A raised stone hearth that stays in place should be excluded, but only its actual footprint. Measure it rather than guessing. Door thresholds where flooring stops at a transition strip should be measured to the centre of the doorway, the usual dividing point between two rooms.

Stair openings, boxed pipework and kitchen island plinths follow the same logic: include what will be covered, exclude what will not, and write the decision down beside the figure so you can defend it later.

Measuring when your tape reads in metres

Many UK and European tapes show centimetres only, and much product packaging lists coverage in square metres. The method does not change, only the arithmetic. Measure length and width in metres to two decimal places, multiply them, and you have square metres directly. A room at 4.50 m by 3.20 m is 14.40 m². To convert square metres into square feet, multiply by 10.7639; to go the other way, divide square feet by the same figure.

Mixing systems mid-calculation is the commonest source of a badly wrong order. Pick one system for the measuring session, finish the whole sketch in it, and convert only the final totals. If a box states coverage as 22.5 sq ft, that is about 2.09 m², and converting the box figure once is safer than converting every wall. When you are ready to turn a finished area into boxes, the Flooring Calculator accepts the area and the box coverage and handles the rounding up to whole boxes for you.

Keep a note of which unit each sketch figure uses. Writing “365” without a unit invites someone to read centimetres as millimetres or inches, and all three interpretations look plausible on paper.

Allowing for walls that are not straight

Older houses rarely offer a perfectly straight wall. Run a long straightedge or a taut string along the skirting and look for gaps. Where a wall bows inward, your plank or tile will need scribing to follow it, and that consumes width. Measure to the furthest intrusion and treat the bowed section as if the room were that wide throughout. It overstates the area slightly, but the alternative is a visible gap that no bead of sealant disguises well.

Doorways deserve a second look too. Measure the width of the opening and note whether flooring continues through into a hall. A continuous run through a doorway changes both the area and the direction planks can sensibly travel, and it removes the natural break where a mistake could be hidden under a threshold bar.

Recording it so the order is right

Finish with a single clean sketch showing every dimension, the total net area, and a note of anything excluded. Add the date and the room name. If you measure three rooms in one afternoon, unlabelled sketches blur together within a week. Keep the sketch until the floor is fitted and you have confirmed you hold a sensible leftover plank or two for future repairs. A measured drawing is also what a supplier needs if you later query a short delivery, so it earns its place in the household file long after the fitting day.


Next step: feed the buy area you measured, not the bare floor area, into the Flooring Calculator with your box coverage, and let it round up to whole boxes. Measuring carefully and then rounding down at the last step undoes the whole exercise.