Tile a Small Bathroom Floor: A Complete Worked Estimate

A full tile estimate for an 8 by 5 foot bathroom floor using 12 by 24 inch tiles with 10 percent waste.

Compact bathrooms reward careful counting because there is nowhere for surplus tiles to hide and no tolerance for running short mid-job, when the toilet is already removed and the room is out of use. The example below follows one small floor from the tape measure to the last box, showing exactly where each tile in the final count comes from.

The floor in question

This bathroom floor is a plain rectangle measuring 8 ft long by 5 ft wide, equivalent to 2.44 m by 1.52 m. The bath is enclosed behind a panel that stays in place, so the tiled area is the exposed floor only, and the doorway is a single straight edge where the tiles meet the landing flooring. There are no diagonal layouts, borders, or feature strips in the design — the tiles run straight, long edge parallel to the long wall.

The chosen tile is a large-format rectangle, 12 in by 24 in, which is 30.5 cm by 61 cm. Large tiles on a small floor mean fewer grout lines and faster coverage, but each individual tile represents a bigger share of the room, so a cutting error costs more of the total area than it would with small mosaics.

Step one: floor area

Multiply length by width:

8 ft × 5 ft = 40 sq ft (3.72 sq m)

That single number drives everything else in this estimate: tile count, adhesive coverage, grout coverage, and underlayment if it is used.

Step two: area covered by one tile

Convert the tile dimensions to feet before multiplying. Twelve inches is 1 ft, and twenty-four inches is 2 ft:

1 ft × 2 ft = 2 sq ft per tile (0.186 sq m)

A useful sanity check follows from that. If the floor were covered with whole tiles and no cuts at all, the count would be:

40 sq ft ÷ 2 sq ft per tile = 20 tiles

Twenty is the theoretical minimum. No real floor achieves it, because edges need cutting and some cuts go wrong, which is why the next step exists.

Step three: add waste for cuts and breakages

A waste allowance of 10 percent is applied to this straight layout:

20 tiles × 10% = 2 extra tiles

20 tiles + 2 tiles = 22 tiles to buy

Equivalently, 40 sq ft × 1.10 = 44 sq ft (4.09 sq m) of tile to purchase, and 44 ÷ 2 = 22 tiles. Both routes arrive at the same answer, which is a good cross-check to run on any tile job.

The Tile Calculator performs this area, tile-size, and waste sequence for other room shapes and tile formats.

Step four: convert tiles into boxes

Tiles are sold in boxes of 10 for this product, so divide the required count by the box quantity and round up:

22 tiles ÷ 10 per box = 2.2 boxes → buy 3 boxes

Three boxes deliver 30 tiles. That leaves 8 tiles beyond the calculated need, which sounds generous until you remember that edge cuts in a 5 ft (1.52 m) wide room consume partial tiles along both long walls. Several of those spares will be cut down rather than laid whole, and the remainder become the attic spares that make a future repair possible without hunting for a discontinued batch.

Full shopping list

Item Quantity needed Buy
Floor tiles, 12 × 24 in (30.5 × 61 cm) 22 tiles including 10% waste 3 boxes of 10
Tile adhesive To cover 40 sq ft (3.72 sq m) at the notch depth for large-format tiles Enough bags for 40 sq ft plus a margin
Grout To fill joints across 40 sq ft of 12 × 24 in tiles 1 bag sized for the area
Tile spacers For consistent joints across the floor 1 pack
Backer board or uncoupling membrane To cover 40 sq ft (3.72 sq m) Sheets totalling at least 40 sq ft
Silicone sealant For the perimeter where floor meets bath panel, walls, and pedestal 1 tube
Threshold strip For the single doorway, 1 doorway width 1 strip
Tile trim or edging Only if an exposed edge is left at the door 1 length

Adhesive and grout are listed by coverage rather than by an invented bag count, because bag yields differ between products. Read the coverage panel on the bag you actually pick up, divide 40 sq ft (3.72 sq m) by that figure, and round up — the same discipline used for the tiles themselves.

Order of work

Start by removing the toilet and pedestal if they sit on the area to be tiled, rather than tiling tightly around their bases; the finish is neater and future plumbing access is far easier. Strip the old flooring, check the subfloor for movement or water damage, and fix backer board or membrane across the full 40 sq ft.

Dry-lay the tiles before mixing anything. In a room only 5 ft (1.52 m) wide, decide in advance where the cut row falls so you do not end with a sliver against the most visible wall. Mark the centre line, lay out a row in each direction, and adjust the starting point until both edges take a respectable cut.

Then set the tiles working away from the far corner toward the door, so you never have to step across fresh adhesive to leave. Butter large-format tiles on the back as well as trowelling the floor, to avoid voids under a tile that spans 2 sq ft (0.186 sq m). Leave the floor undisturbed until the adhesive has cured, grout the joints, wipe the haze in stages, and finish with silicone around the perimeter rather than grout, because that junction needs to flex.

Guidance on getting the initial measurements right is in how to measure for tile.

Mistakes specific to this project

Tiling around a toilet base instead of lifting the toilet is the classic small-bathroom shortcut, and it causes two problems: the cut is hard to make watertight, and replacing the toilet later leaves an untiled footprint. Lift it, tile under it, refit with a new seal.

Another frequent slip is ordering exactly 20 tiles because the division came out clean. That count assumes zero cuts, zero breakages, and zero flawed tiles in the box. The 10 percent allowance bringing the order to 22 tiles, and the box rounding to 3 boxes, are not padding — they are the difference between finishing on the day and waiting for a second delivery.

People also underestimate how much a large tile telegraphs a wavy subfloor. A 24 in (61 cm) edge bridges dips and then rocks or lips against its neighbour. Spend the extra hour on flattening the base; it is invisible work that decides whether the visible work looks right.

Lastly, keep grout out of the perimeter joint. Rigid grout where the floor meets a bath panel or wall tends to crack as the building moves slightly. That joint belongs to flexible silicone, every time.


Next step: measure your own bathroom floor, including the awkward cuts around your fixtures, and run it through the Tile Calculator. If your box count matches this page's three, check the batch numbers on delivery with the same care shown here.